RA6M1

Detailed Description

Build Time Configurations for ra6m1_fsp

The following build time configurations are defined in fsp_cfg/bsp/bsp_mcu_family_cfg.h:

Configuration	Options	Default	Description
OFS0 register settings
OFS0 register settings > Independent WDT
Start Mode	IWDT is stopped after a reset IWDT is automatically activated after a reset (Autostart mode)	IWDT is stopped after a reset
Timeout Period	128 cycles 512 cycles 1024 cycles 2048 cycles	2048 cycles
Dedicated Clock Frequency Divisor	1 16 32 64 128 256	128
Window End Position	75% 50% 25% 0% (no window end position)	0% (no window end position)
Window Start Position	25% 50% 75% 100% (no window start position)	100% (no window start position)
Reset Interrupt Request Select	NMI request or interrupt request is enabled Reset is enabled	Reset is enabled
Stop Control	Counting continues (Note: Device will not enter Deep Standby Mode when selected. Device will enter Software Standby Mode) Stop counting when in Sleep, Snooze mode, or Software Standby	Stop counting when in Sleep, Snooze mode, or Software Standby
OFS0 register settings > WDT
Start Mode Select	Automatically activate WDT after a reset (auto-start mode) Stop WDT after a reset (register-start mode)	Stop WDT after a reset (register-start mode)
Timeout Period	1024 cycles 4096 cycles 8192 cycles 16384 cycles	16384 cycles
Clock Frequency Division Ratio	4 64 128 512 2048 8192	128
Window End Position	75% 50% 25% 0% (no window end position)	0% (no window end position)
Window Start Position	25% 50% 75% 100% (no window start position)	100% (no window start position)
Reset Interrupt Request	NMI Reset	Reset
Stop Control	Counting continues Stop counting when entering Sleep mode	Stop counting when entering Sleep mode
OFS1 register settings
Voltage Detection 0 Circuit Start	Voltage monitor 0 reset is enabled after reset Voltage monitor 0 reset is disabled after reset	Voltage monitor 0 reset is disabled after reset
Voltage Detection 0 Level	2.94 V 2.87 V 2.80 V	2.80 V
HOCO Oscillation Enable	HOCO oscillation is enabled after reset HOCO oscillation is disabled after reset	HOCO oscillation is disabled after reset
MPU
Enable or disable PC Region 0	Enabled Disabled	Disabled
PC0 Start	Value must be an integer between 0 and 0xFFFFFFFC	0xFFFFFFFC
PC0 End	Value must be an integer between 0x00000003 and 0xFFFFFFFF	0xFFFFFFFF
Enable or disable PC Region 1	Enabled Disabled	Disabled
PC1 Start	Value must be an integer between 0 and 0xFFFFFFFC	0xFFFFFFFC
PC1 End	Value must be an integer between 0x00000003 and 0xFFFFFFFF	0xFFFFFFFF
Enable or disable Memory Region 0	Enabled Disabled	Disabled
Memory Region 0 Start	Value must be an integer between 0 and 0x00FFFFFC	0x00FFFFFC
Memory Region 0 End	Value must be an integer between 0x00000003 and 0x00FFFFFF	0x00FFFFFF
Enable or disable Memory Region 1	Enabled Disabled	Disabled
Memory Region 1 Start	Value must be an integer between 0x1FF00000 and 0x200FFFFC	0x200FFFFC
Memory Region 1 End	Value must be an integer between 0x1FF00003 and 0x200FFFFF	0x200FFFFF
Enable or disable Memory Region 2	Enabled Disabled	Disabled
Memory Region 2 Start	Value must be an integer between 0x400C0000 and 0x400DFFFC or between 0x40100000 and 0x407FFFFC	0x407FFFFC
Memory Region 2 End	Value must be an integer between 0x400C0003 and 0x400DFFFF or between 0x40100003 and 0x407FFFFF	0x407FFFFF
Enable or disable Memory Region 3	Enabled Disabled	Disabled
Memory Region 3 Start	Value must be an integer between 0x400C0000 and 0x400DFFFC or between 0x40100000 and 0x407FFFFC	0x400DFFFC
Memory Region 3 End	Value must be an integer between 0x400C0003 and 0x400DFFFF or between 0x40100003 and 0x407FFFFF	0x400DFFFF
Clocks
HOCO FLL Function	Enabled Disabled	Disabled	Setting this option to Enabled improves HOCO accuracy significantly by using the subclock, but incurs certain restrictions. The FLL function requires the subclock oscillator to be running and stabilized. When enabled and running the PLL or system clock from HOCO, the BSP will wait for both the Subclock Stabilization Time as well as the FLL Stabilization Time when setting up clocks at startup. When FLL is enabled Software Standby and Deep Software Standby modes are not available.
MOSC Drive Capability Auto Switching	Enabled Disabled	Disabled	When enabled, the drive capability auto switching function lowers the MOSC drive capability automatically after the MOSC starts and suppresses the EMI associated with the MOSC.
Main Oscillator Wait Time	35 cycles 67 cycles 131 cycles 259 cycles 547 cycles 1059 cycles 2147 cycles 4291 cycles 8163 cycles	8163 cycles	Number of cycles to wait for the main oscillator clock to stabilize.
Enable inline BSP IRQ functions	Enabled Disabled	Enabled	Using static inline functions will slightly increase code size, but will slightly decrease cycles taken in ISRs in return.
ID Code Mode	Unlocked (Ignore ID) Locked with All Erase support Locked	Unlocked (Ignore ID)	When set to 'Locked with All Erase support', the ID Code must be set in the debugger to read or write data to the MCU, but the All Erase command is still accepted regardless. When set to 'Locked', all erase/download/debug access is disabled unless the ID Code is provided.
ID Code (32 Hex Characters)	Value must be a 32 character long hex string	FFFFFFFFFFFFFFFFFFFFFFFFFFFFFFFF	Set the ID Code for locking debug access. This setting is only used when the ID Code Mode is not set to Unlocked.

Macros
#define	BSP_ELC_PERIPHERAL_MASK

Enumerations
enum	elc_event_t
enum	elc_peripheral_t

Macro Definition Documentation

BSP_ELC_PERIPHERAL_MASK

#define BSP_ELC_PERIPHERAL_MASK

Positions of event link set registers (ELSRs) available on this MCU

Enumeration Type Documentation

elc_event_t

enum elc_event_t

Sources of event signals to be linked to other peripherals or the CPU

Note

This list is device specific.

elc_peripheral_t

enum elc_peripheral_t

Possible peripherals to be linked to event signals

Note

This list is device specific.