![]() |
RA Flexible Software Package Documentation
Release v6.0.0
|
|
Configuration | Options | Default | Description |
---|---|---|---|
Security | |||
Security > Exceptions | |||
Exception Response |
| Non-Maskable Interrupt | Configure the result of a TrustZone Filter exception. This exception is generated when a the TrustZone Filter detects access to a protected region. This setting is only valid when building projects with TrustZone. |
BusFault, HardFault, and NMI Target |
| Secure State | Value for SCB->AIRCR register bit BFHFNMINS. Defines whether BusFault and NMI exceptions are Non-secure, and whether exceptions target the Non-secure HardFault exception. This setting is only valid when building projects with TrustZone. |
Prioritize Secure Exceptions |
| Disabled | Value for SCB->AIRCR register bit PRIS. When enabled, all Non-secure interrupt priorities are automatically demoted by right shifting their priority by one then setting the most significant bit. As there is effectively one less bit care must be taken to ensure the prioritization of non-secure interrupts is correct. This setting is only valid when building projects with TrustZone. |
Security > SRAM Accessibility | |||
SRAM1 Protection |
| Both Secure and Non-Secure State | Defines whether SRAMCR1, and SRAMESCLR.CLR1 are write accessible for the Non-secure application. This setting is only valid when building projects with TrustZone. |
Standby SRAM Protection |
| Both Secure and Non-Secure State | Defines whether STBRAMCR, and SRAMESCLR.CLRS are write accessible for the Non-secure application. This setting is only valid when building projects with TrustZone. |
Security > BUS Accessibility | |||
Bus Security Attribution Register A |
| Both Secure and Non-Secure State | Defines whether the Slave Bus Control Registers (BUSSCNT<slave>) are write accessible for the Non-secure application. This setting is only valid when building projects with TrustZone. |
Bus Security Attribution Register B |
| Both Secure and Non-Secure State | Defines whether the Bus and DMAC/DTC Error Clear Registers are write accessible for the Non-secure application. This setting is only valid when building projects with TrustZone. |
System Reset Request Accessibility |
| Secure State | Value for SCB->AIRCR register bit SYSRESETREQS. Defines whether the SYSRESETREQ bit is functional for Non-secure use. This setting is only valid when building projects with TrustZone. |
System Reset Status Accessibility |
| Both Secure and Non-Secure State | Defines whether the reset status registers (RSTSRn) can be cleared from the Non-secure application. This setting is only valid when building projects with TrustZone. |
Battery Backup Accessibility |
| Both Secure and Non-Secure State | Defines whether the battery backup registers are accessible for the Non-secure application. If Secure State is selected, all battery backup registers are read only except for VBTBKRn registers which are both read and write protected. This setting is only valid when building projects with TrustZone. |
Uninitialized Non-Secure Application Fallback |
| Enable Uninitialized Non-Secure Application Fallback | If enabled, the secure application checks if the non-secure application has been programmed in non-secure flash before branching. If the non-secure application has not been programmed, then the secure application branches to an infinite loop in non-secure RAM. This prevents an issue where the debugger may not connect if the MCU is configured in the NSECSD lifecycle state. |
Clocks | |||
HOCO FLL Function |
| Disabled | Setting this option to Enabled improves HOCO accuracy significantly by using the subclock, but incurs certain restrictions. The FLL function requires the subclock oscillator to be running and stabilized. When enabled and running the PLL or system clock from HOCO, the BSP will wait for both the Subclock Stabilization Time as well as the FLL Stabilization Time when setting up clocks at startup. When FLL is enabled Software Standby and Deep Software Standby modes are not available. |
Clock Settling Delay |
| Enabled | Setting this option to Enabled will insert delays for clocking scaling and transitions to ensure voltage supply stability. See the RA8E1 HWM (R01UH1129EJ0100) section 8.11.1 for details. |
Sleep Mode Entry and Exit Delays |
| Enabled | Setting this option to Enabled will insert delays before and after entering sleep modes to ensure voltage supply stability. This is not required if you do not intend to run CPUCLK over 120MHz. See RA8E1 HWM (R01UH1129EJ0100) Section 10.8.10 for details. |
RTOS Sleep on Idle |
| Disabled | Setting this option to Enabled will allow RTOS ports to enter CPU Sleep mode while idle. This should not be used when CPUCLK is configured over 120MHz. See RA8E1 HWM (R01UH1129EJ0100) Section 10.8.10 for details. |
MSTP Change Delays |
| Enabled | Setting this option to Enabled will insert delays after setting a MSTP bit to ensure voltage supply stability. This is not required if you do not intend to run CPUCLK over 120MHz. See RA8E1 HWM (R01UH1129EJ0100) Section 10.4 for details. |
Settling Delay (us) | Unit must be a non-negative integer | 150 | Specifies the length of the delay to be used for the Clock settling, Sleep mode, and MSTP change delays. |
Cache settings | |||
Data cache |
| Disabled | Enable limited D-Cache support. See BSP usage notes for limitations. |
Enable inline BSP IRQ functions |
| Enabled | Using static inline functions will slightly increase code size, but will slightly decrease cycles taken in ISRs in return. |
Main Oscillator Wait Time |
| 8163 cycles | Number of cycles to wait for the main oscillator clock to stabilize. |
Enabled | Hidden Property - Force D-Cache to use write-through for all cacheable writes. |
Macros | |
#define | BSP_ELC_PERIPHERAL_MASK |
Enumerations | |
enum | elc_event_t |
enum | elc_peripheral_t |
#define BSP_ELC_PERIPHERAL_MASK |
Positions of event link set registers (ELSRs) available on this MCU
enum elc_event_t |
Sources of event signals to be linked to other peripherals or the CPU
enum elc_peripheral_t |
Possible peripherals to be linked to event signals